XP and XP-h Proportioners |
Maximum Fluid Working Pressure |
See Models section in instruction manual. |
Maximum Air/Hydraulic Oil Working Pressure |
See Models section in instruction manual. |
Combined Fluid Output (cc/cycle) |
See Models section in instruction manual. |
Pressure Ratio |
See Models section in instruction manual. |
Fluid Flow at 40 cpm |
See Models section in instruction manual. |
Hydraulic Fluid Consumption (XP-h models only) |
0.2 gallons per cycle |
Air inlet size |
3/4 npsm(f) |
Maximum air pressure supply to the system |
175 psi |
Fluid pump inlets without hoppers |
1-1/4 in. npsm(m) |
Fluid gauge manifold outlets |
1/2 in. npt(f) |
Fluid mix manifold inlets |
1/2 in. npt(f) ball valves |
Mix manifold material outlet |
1/2 in. npt(f) |
Maximum feed pressure from remote source |
250 psi |
Sound pressure |
86 dBA at 100 psi |
Sound power |
98 dBA at 100 psi |
Maximum Storage Time |
5 years (To maintain original performance, replace soft seals after 5 years of inactivity.) |
Maximum Lifetime |
Indefinite with recommended maintenance and periodic rebuilds for critical parts. |
Power Efficiency Factor (XP70) |
75 cu. ft compressed air/1 gallon sprayed material at 100 psi |
Air consumption per 1 gallon (3.78 l) of flow |
XP70 |
75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa) |
XP50 |
60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa) |
XP35 |
50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa) |
Filtration |
Air inlet filtration |
40-micron filter/separator included |
XP pump outlets |
30 mesh |
XTR Spray Gun |
60 mesh |
Fluid Viscosity Range |
Gravity feed with 7 gallon (26 liter) hoppers |
200 to 20,000 cps (pourable) |
Pressure feed |
Any viscosity that will not require feed pressure more than 15% of outlet pressure |
Environmental Rating (Indoor/outdoor) |
Hazardous Areas |
EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated. |
Ambient Temperature Range |
Operating |
40-130°F |
Storage |
30-160°F |
Maximum Fluid Temperature |
160°F |
Wetted materials |
Housings and manifolds |
Carbon steel with electroless nickel plating |
Miscellaneous parts |
Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics |
Pump packings |
Carbon filled PTFE, proprietary UHMWPE |
Flush pump suction tube |
Aluminum |
Hoses |
Nylon core |
Weight |
Full XP35, XP50, or XP70 System with heaters, solvent flush pump, and hoppers |
575 lb |
Full XP-h System with heaters, solvent flush pump, and hoppers |
600 lb |
Bare XP35, XP50, or XP70 system with no heaters, solvent flush pump, or hoppers |
425 lb |
Bare XP-h System with no heaters, solvent flush pump, or hoppers |
450 lb |
XP35, XP50, or XP70 Pump only |
286 lb |
XP-h Pump only |
290 lb |